What is the standard size of fascia?

What is the standard size of fascia?

Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.

How do I know my fascia size?

Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch. For a 2×6 fascia board at a 4/12 slope, the trim size would be 1-1/2 inch x 5 inches for an overhang without a soffit.

What size is timber fascia?

The timber fascia board sizes available in this profile are 180×25, 188×30, 210×30, and 230×30. One product variation with size 188×30 is included in this profile.

What board do you use for fascia board?

Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.

How thick is a soffit board?

Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.

What is the height of a fascia board?

Fascia Board Sizes #1 – 1×6 This is the most common fascia board you will find. Usually you have a 2×4 sub fascia behind this fascia board. Standard gutter size for residential homes is five or six inches. At the backside of a 5 inch gutter, the fascia board mounting area will be four inches tall.

How do you measure soffit and fascia?

Multiply the total length by the width to obtain the area of soffit needed to fill the gap. For example, if the total eaves length is 110 feet, and the width is 2 feet, multiply 110 by 2. The result, 220 in this example, is the number of square feet of soffit required.

What is design pine?

Design Pine is a range of structural and decorative timber products coated with a genuine primer. All finger jointed primed pine products are made up of four key components, these being the timber, the preservative, the glue system, and the primer system.

What are the boards around the bottom of a house?

In architecture, a baseboard (also called skirting board, skirting, wainscoting, mopboard, floor molding, or base molding) is usually wooden or vinyl board covering the lowest part of an interior wall.

Can PVC be used for fascia board?

PVC as a Fascia Material It’s most appropriate for houses with vinyl or aluminum siding, but it adds a clean touch to a house with wood, brick or stone siding as well. PVC fascia board comes in a variety of colors, and it’s paintable.

Should I use treated lumber for fascia board?

Should the fascia board be pressure treated? – Quora. It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.

What is the standard size of fascia board?

The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches. Click to see full answer Beside this, how do I know my fascia size?

How big is a 1×10 in inches?

That means a 1×10 is actually 3/4 inch in thickness by 9 1/4 inches. 2×4 and 2×6 boards lose 1/2 inch in thickness and 1/2 inch in width before leaving the mill. That means a 2 x 4 board is actually 1-1/2 inches by 3-1/2 inches. The larger 2x boards (2×8, 2×10, etc.) lose 3/4 inch in width.

What kind of wood is used for fascia?

Wood Fascia Boards Wood is the most common material used to make fascia. Typically, wood fascia boards are made of spruce, pine or fir. However, cedar fascia boards (same wood for decks) are gaining steam. Also to know, how long is a piece of fascia?

How big is a 1×4 board in inches?

1x Board Sizes 1×4 and 1×6 boards lose 1/4 inch in thickness and 1/2 inch in width before leaving the mill. That means a 1 x 4 board is actually 3/4 inches by 3 1/2 inches. The larger 1x boards (1×8, 1×10, etc.) lose 3/4 inch in width.