Table of Contents
How do you tell what Dodge rear end you have?
if you look at the sticker behind your grille on the inside of the hood it will list the axles and gear ratios. the rear axle should have a sticker on top of it right next to the driver side brake drum that will have the gear ratio. it will say either 3.55 or 3.92.
How much does it cost to replace a rear axle on a truck?
The rear axle is usually more expensive to repair or replace. It can cost anywhere from $450 to over $1,000 for the rear axle, but most people pay between $600 – $900. The cost for the rear axle will depend heavily on whether the vehicle is four wheel drive, front wheel drive, or rear wheel drive.
Did Dodge stop using Dana axles?
Dodge used a Dana 60 up to 2002. 3rd Generation Dodge Rams dropped the Dana 60 in favor of AAM (American Axle & Manufacturing) axles. Ford still uses the Dana 60 front axle.
What is a rear end on a truck called?
A rear end, or a “rear axle assembly”, allows the transfer of power from your transmission to your wheels. An axle houses the differential, axle shafts, bearings, seals, and mounts that are needed to make this power transfer work.
Can you fix bent rear axle?
In most cases a bent axle cannot be repaired and must be replaced. A bad axle will lead to other damage to your vehicle down the line. So it’s critical that the axle be in great condition to avoid other costly repairs.
Does a broken rear axle total a car?
If the crash results in a broken axle, dented or tweaked pillar (the parts that “hold up” the roof, including the front windshield frame, the part between your front and rear doors, and the rear roofline), or extensive damage to the drivetrain or under-hood components, you could be looking at a total loss.
What does a Dana 80 look like?
It can be identified by its straight axle tubes, 10 bolt asymmetrical cover, and a “80” cast into the housing. Dana 80’s are made as full floating, rear axles only and are step up in overall strength compared to the Dana 70. 1988 Ford was the first company to use the Dana 80.
Is Dana 80 a good axle?
Heavy Hitter. The super-tough Dana 80 rear axle ranks as one of the most desirable axles for off-highway use. It has an 11,000-pound gross axle weight rating and a continuous manufacturer’s output torque rating of 2,500 lb-ft.
Which type of axle is used in trucks?
Semi-floating axles are used for cars, SUVs, and mid-size trucks, such as half-ton and light duty pickups. Full-Floating Axle: True to its name, this axle type effectively floats in place and maintains its position, thanks to two bearings. It’s designed to transmit driving torque only.
What are the types of rear axle?
Depending upon the methods of supporting the rear axles and mounting the rear wheels, the three types of rear axles are as follows:
- Semi-floating axle.
- Full-floating axle.
- Three quarter floating axle.
What kind of rear axle does a Chevy pick up have?
Not all vehicles are set up the same, even though they may be the same make and model. A Chevy 1/2 ton pick-up may have a Chevy 10 bolt rear axle or a 12 bolt rear axle. Both of these are semi-floating axles.
What are the dimensions of a rear axle?
Rear axle widths. These dimensions do not include brake drums and are measured from backing plate to backing plate. Actual wheel track could be as much as 6″ to 8″depending on drum size: 46″ to 47″. ’66 to ’77 Bronco. 48″ to 49″. ’72 to ’75 Datsun pickup.
How can I find out what rear axle I have?
The best way to be sure of which axle you have is by the Bill of Material Number stamped on the right hand axle tube. See the Spicer Axle Identification information. GMC / CHEVY REAR AXLES. Find your GMC/Chevy vehicle in the chart below and click on the illustration for a larger view.
How big is a rear axle wheel track?
These dimensions do not include brake drums and are measured from backing plate to backing plate. Actual wheel track could be as much as 6″ to 8″depending on drum size: