Table of Contents
- 1 How many pins does a IDE connector have?
- 2 What is IDE cable?
- 3 What is the maximum recommended length of an IDE?
- 4 How many pins does SATA cable have?
- 5 How many IDE devices can you have in a PC?
- 6 How many pins does a SATA connector have?
- 7 How many IDE devices can connect on a single IDE channel?
- 8 How many wire connectors does an IDE cable have?
- 9 Is there a 2.80 pin IDE / ATA cable?
How many pins does a IDE connector have?
Parallel ATA
| Production history | |
|---|---|
| External | No |
| Cable | 40 or 80 conductor ribbon cable |
| Pins | 40 |
| Data |
What is IDE cable?
IDE, an acronym for Integrated Drive Electronics, is a standard type of connection for storage devices in a computer. Generally, IDE refers to the types of cables and ports used to connect some hard drives and optical drives to each other and to the motherboard.
What is the maximum recommended length of an IDE?
The maximum length is actually 18 inches from the IDE device to the IDE controller. You can have a 36 inch cable, as long as the IDC connector at the 18 inch mark is connected to the IDE controller.
What is the connector of an 80 wire IDE data cable gets connected to the master drive?
If using the 80-wire cable, attach the blue end connector to the system board or host controller, the gray middle connector to the Slave, and the black end connector to the Master. All newer IDE/EIDE hard drives can be jumpered as Cable Select (CS or CSEL).
What is the purpose of the extra 40 wires in an 80 wire IDE cable?
The extra wires in an 80-wire cable aren’t used to pass traffic, but they can reduce the amount of crosstalk between the signal wires. This becomes especially important as the speed increases.
How many pins does SATA cable have?
The Serial ATA (SATA) Power connector has 15 pins and is slightly larger than the SATA data connector. One main advantage the SATA power connector provides over the 4 pin power connector is a pin that provides 3.3 V of power. Certain SATA drives have specific power requirements.
How many IDE devices can you have in a PC?
Most motherboards that support IDE (EIDE/ATA) have two IDE interfaces, each interface supports the maximum of two devices. Therefore, you can only have a maximum of four IDE (EIDE/ATA) devices connected to your motherboard.
How many pins does a SATA connector have?
15 pins
While a SATA power cable has 15 pins, SATA data cables have just seven.
How many pins does a SATA internal data cable have?
SATA (Serial Advanced Technology Attachment) has two main connector types. The power connector is larger with 15 pins, while the data connector is 7 pins.
What are three types of technologies are used inside hard drives?
What three types of technologies are used inside hard drives? Solid State Drive, Magnetic Hard Drive, and Hybrid Hard Drive.
How many IDE devices can connect on a single IDE channel?
A single IDE interface can support two devices. Most motherboards come with dual IDE interfaces (primary and secondary) for up to four IDE devices. Because the controller is integrated with the drive, there is no overall controller to decide which device is currently communicating with the computer.
How many wire connectors does an IDE cable have?
The cable has 40 wire connectors in it, and usually has three identical female connectors: one is intended for the IDE controller (or motherboard header for PCs with built in PCI ATA controllers) and the other two are for the master and slave devices on the interface.
Is there a 2.80 pin IDE / ATA cable?
2. 80 PIN IDE/ATA CABLE Requirement: The 80-conductor cable was first defined with the original Ultra DMA modes 0, 1 and 2, covering transfer speeds up to 33.3 MB/s Cable Select Support and Drive Assignment: All 80-conductor cables that meet the ATA specifications support the cable select feature automatically.
What are the requirements for an 80 conductor cable?
Requirement: The 80-conductor cable was first defined with the original Ultra DMA modes 0, 1 and 2, covering transfer speeds up to 33.3 MB/s Cable Select Support and Drive Assignment: All 80-conductor cables that meet the ATA specifications support the cable select feature automatically.
What’s the difference between Gray and black IDE cable?
Gray: The gray connector is in the middle of the cable, and goes to any slave (device 1) drive if present on the channel. Black: The black connector is at the opposite end from the host connector and goes to the master drive (device 0), or a single drive if only one is used.
https://www.youtube.com/watch?v=trqMYY5XBr4