Table of Contents
- 1 What are DIN rail products?
- 2 What are DIN rails used for?
- 3 What are the different types of DIN rail?
- 4 What is a top hat DIN rail?
- 5 What is a DIN enclosure?
- 6 Are DIN rails grounded?
- 7 Should DIN rail be earthed?
- 8 What are DIN rail terminal blocks?
- 9 What can be mounted on a DIN rail?
- 10 What’s the difference between DIN rails and Ts15 rails?
What are DIN rail products?
A DIN rail is a standard type metal rail that is utilized for mounting circuit breakers and industrial control equipment in equipment racks. In addition, it acts as a mechanical support structure for different types of small electrical parts.
What are DIN rails used for?
DIN rails are the metal rails inside an electrical enclosure that are used to mount circuit breakers and other types of electrical equipment. Although DIN rails have a relatively simple design, they’re extremely important for the installation, maintenance and operation of electrical equipment.
What are the different types of DIN rail?
Types. There are three major types of DIN rail: Top hat section (TH), type O, or type Ω, with hat-shaped cross section.
What does DIN in DIN rail stand for?
Deutsches Institut fur Normung
DIN stands for “Deutsches Institut fur Normung”, which means “German Institute for Standardization.” In the 1970’s the name DIN became the official symbol for technical standardization in Germany. It has become commonplace for Automation equipment to be mounted on 35mm DIN rails.
How much weight can a DIN rail hold?
It can hold components up to 1.1lbs in weight. DIN rails can be mounted simply by using several STEGOFIX units. If the weight of attached components exceeds the load limit or if a more secure mounting is desired, it can also be screw-mounted.
What is a top hat DIN rail?
DIN rails, 7.5 mm The TS-35 rail or Top Hat as it is also known is manufactured from cold rolled steel which is then zinc coated and clear passivated.
What is a DIN enclosure?
DIN rail enclosures – also known as top hat rail enclosures – are often used for applications in measurement, control and instrumentation applications. Whether plastic or metal, with or without a BUS connection, with or without air vents: the range of this special type of enclosure is huge.
Are DIN rails grounded?
DIN rail can’t be considered bonded to the ground plane because the screws are “mounting screws” and not “bonding screws.”…
Can DIN rails be mounted vertically?
Yep.. You can mount DIN rail any way the things you’re going to mount on it allow. Vertical mountings need end-stops that will hold for the conditions the system will be subjected to.
Can DIN rail be used for grounding?
With the use of a DIN rail ground (protective conductor) terminal block, the DIN rail itself can be used as the grounding busbar. This system allows all control components and their ground requirements to be placed on the same rail and in the same location (a separate ground busbar is no longer required).
Should DIN rail be earthed?
oEach DIN rail must be connected to the protective earth of the enclosure. A stainless steel DIN rail is recommended rather than an aluminum one in order to provide the most consistent earthing.
What are DIN rail terminal blocks?
DIN rail terminal blocks are made from plastic or other insulating materials. They provide a safe interface between different components on and sections of the DIN rail. DIN is an acronym for Deutsche Institut für Normung, the German Institute for Standardisation.
What can be mounted on a DIN rail?
TS35 DIN rail is very commonly used for mounting a wide range of of electrical industrial control products and components, from circuit breakers and motor controllers to remote I/O, transformers, drives and much more.
What are the dimensions of the Erico DIN rail?
ERICO offers DIN Rails available in 35mm x 7.5mm and 35mm x 15mm x35mm with high profile slotted and unslotted available too. On-line Electronics offers a complete line of metal Din Rail. This Din Rail product comes in 1-meter and 2-meter lengths and 15mm, 32mm and 35mm widths.
How does Puls DIN rail power supply work?
PULS DIN rail power supplies are convection-cooled. This means that the electronics are cooled only by a natural air flow. No fans are used, which has a positive effect on the reliability of the power supplies. With every mechanical element, such as a fan, the probability of failure and thus the maintenance requirements also increase.
What’s the difference between DIN rails and Ts15 rails?
As you might expect, the miniature top hat or TS15 DIN rails are the same shape as the above type, only smaller. The two standards differ predominantly in terms of their edge-to-edge width, with TS15 rails measuring just 15mm wide.