Table of Contents
- 1 What is the density of ferric chloride?
- 2 How do you mix ferric chloride and water?
- 3 What is the viscosity of ferric chloride?
- 4 What is the SG of ferric chloride?
- 5 What is ferric acid used for?
- 6 Does ferric chloride lower pH?
- 7 How much does one cubic foot of ferric chloride weigh?
- 8 What should the temp of ferric chloride be?
What is the density of ferric chloride?
2.9 g/cm³
Iron(III) chloride/Density
How do you mix ferric chloride and water?
I mix mine 4:1 with distilled water. That’s 4 parts water to 1 part Ferric Chloride. Store it in something plastic. Add the acid to the water, not the water to the acid.
What happens when you add ferric chloride to water?
When dissolved in water, iron(III) chloride undergoes hydrolysis and gives off heat in an exothermic reaction. The resulting brown, acidic, and corrosive solution is used as a flocculant in sewage treatment and drinking water production, and as an etchant for copper-based metals in printed circuit boards.
How much does ferric chloride cost?
Pricing for ferric chloride is in the range of $300 to $340 per ton, technical grade, 100 percent basis, tanks, f.o.b. works.
What is the viscosity of ferric chloride?
12 cP
Iron(III) chloride
| Names | |
|---|---|
| Viscosity | 12 cP (40% solution) |
| Structure | |
| Crystal structure | Hexagonal, hR24 |
| Space group | R3, No. 148 |
What is the SG of ferric chloride?
Click here for more Density-Concentration Calculators.
| Ferric Chloride Solutions in Water | ||
|---|---|---|
| Temperature in degrees Centigrade (°C) | ||
| 1 | 1.009 | 1.007 |
| 4 | 1.036 | 1.033 |
| 8 | 1.072 | 1.068 |
What is the pH of ferric chloride?
2.0
Very hygroscopic. Slightly water soluble, where a 0.1M solution has a pH of 2.0.
Can you etch aluminum with ferric chloride?
Do NOT use ferric chloride on aluminum. Metal as thin as 24-gauge can be etched – just leave it in for less time than you would for thicker metal. If you want to etch both sides or etch really deeply, use 20-gauge metal or thicker.
What is ferric acid used for?
The primary use of ferric chloride is to remove impurities in water and for wastewater treatment. Ferric chloride is also one of the few water treatment chemicals that can sequester odors.
Does ferric chloride lower pH?
Iron-based coagulants, such as ferric chloride, ferric sulphate and PFS®, are not that popular in Australia and tend be more expensive than alum on an equivalent dose basis. They also consume more alkalinity than alum, and hence tend to depress pH of the dosed water much more.
Does Walmart sell ferric chloride?
MG Chemicals 415-500ML Ferric Chloride – Walmart.com.
Can you etch stainless steel with ferric chloride?
Ferric chloride is normally mixed with water in equal parts to form hydrochloric acid in solution. It’s more commonly used to etch copper, but it also works well to etch stainless steel. It also works with a wider range of resist materials than pure acids do; however, it can pit the surface if not attended to properly.
How much does one cubic foot of ferric chloride weigh?
Weight of the selected item is calculated using its density and entered volume. How many moles in 1 cubic centimeter of Ferric chloride? 1 cubic foot of Ferric chloride weighs 180.91623 pounds [lbs]
What should the temp of ferric chloride be?
Warm the ferric chloride solution between 35 to 55 °C [95 to 131 °F]. ATTENTION! Do NOT heat ferric chloride solution above 55 °C [131 °F]. NOTE: Dilution is not recommended. 2
Do you have to dilute ferric chloride with water?
I diluted it with water, and have been using it for years without any trouble. I use it in a flat tray with the plate lying in the tray face up, and enough ferric chloride solution to cover the plate.
What kind of odor does ferric chloride have?
CAMEO Chemicals Ferric chloride, solution appears as a colorless to light brown aqueous solution that has a faint hydrochloric acid odor. Highly corrosive to most metals and probably corrosive to tissue.