Can you swap a 4L60E for a TH400?

Can you swap a 4L60E for a TH400?

that is/was a popular swap for the 700r4s, but i don’t know of anyone swapping a 4l60e for a 400. it can be done, but if you are carrying all that weight, and if you use overdrive, then a 4l80 or 4l85 e is the way to go.

Is TH400 same length as 4L60E?

The 4L60e and the TH400 have their differences, as you can imagine. The 4l60e, which measures 30.75-inches, is a little longer than the short tail TH400 at 28.25-inches. As you might expect, the 4L80e is the longer of the three transmissions, with a length of 32.187-inches.

What engines fit a 4L60E?

In most cases, you can use the 4L60E trans with its 298mm style converter behind a normal, six-bolt LS crank flange engine (4.8L, 5.2L, 5.7L, 6.0L, and 6.2L). Truck engines such as the 4.8L, 5.3L, and 6.0L used a dished flexplate to place the starter ring gear in the correct position.

Is the TH400 a good transmission?

The TH400 is an automatic shift, three-speed, longitudinally positioned transmission. It is widely regarded to be a supremely durable and legendary transmission.

Will a Turbo 400 replace a 4L80E?

Very easy. So is just buying the aluminum circle pattern 4L80E pedestal which has the same transfer case bolt pattern. So, if you have a TH400 to NP205 mount, just a bit of work will make it bolt up to a 4L80E and all is well.

What is the length of a TH400 transmission?

24-3/8″ long
The 400 transmission has a main case of cast aluminum alloy with a length of 24-3/8″ long. Its aluminum case is essentially smooth.

Is a TH400 the same size as a 4L80E?

4L80E transmissions have nearly 25% overdrive and are 4 inches longer than the TH400. The trans mount has been moved rearward by an inch-and-a-half. If we talk about the weight, the 4L80E is nearly 50 pounds heavier compared to the TH400 due to the electronic control.

How can I make my 4L60E stronger?

Now, let’s dive in:

1. Lay out the important parts on an assembly bench.
2. Rebuild with an improved, thicker sun shell.
3. Use five-pinion front/rear planetary.
4. Use a larger clutch with an input drum reinforcement sleeve.
5. Stamped Steel forward clutch apply pistons.
6. Use more clutches and larger gear band servo pistons.

How much does it cost to rebuild a 4L60E?

The Cost of Rebuilding a Store from the 4L60E If you plan to remodel the store and get the remittance there, you can do it for $ 1,000 or less. But not much of that. If you have a company that rebuilds and reinstalls the gearbox, it can cost anywhere from $ 2,000 to $ 4,000.

Will a 4L60E bolt up to a 400 small block?

You’re trans (4L60E) will bolt right up to a small block, no adapters needed.

How does a TH400 work?

The TH400 transmission takes advantage of an electrical slide switch controlled by the throttle linkage. On the other hand, the TH350 uses a mechanical cable kick-down that is connected to the throttle linkage. Despite the difference, the TH400 is considered the heavy-duty version of the Turbo-Hydramatic 350.

What’s the difference between the 4L60E and 4L80E?

The 4L80e is much larger and heavier than the 4L60E. The 4L60E has a weight of 150 lbs without fluid and a length of 23.5″, while the 4L80e has a weight of 236 lbs and a length of 26.4″. Just with these numbers, you can probably calculate that there is a big difference in size and weight between these transmissions. 2.

Can a TH-400 be converted to a 4L80E?

Plus, with the lockup clutch, it works very well once the trans shifts into high gear. Of course, this conversion will also require a new driveshaft as the 4L80E is longer than the typical short tailshaft TH-400 that is currently in your car.

How much torque can a 4L60E transmission handle?

The 4l60e transmission can handle a max torque of around 350nm, while the 4l80e can handle 450nm~ or even more. These numbers can differ a lot and you will get a lot of different answers about how much these can handle. We have to remember that there is a big difference in the durability between a 30-year-old transmission and a new one.

Can a Chevy 4L60E be used in a big block truck?

The easiest way to adapt an electronic 4L60E to an earlier Gen I small- or big-block Chevy is to use one of the earlier small-block 4L60E boxes located behind small-blocks used in trucks and pre-’98 cars.