Table of Contents
- 1 How do I reset my John Deere hour meter?
- 2 How do you read the hours on a John Deere tractor?
- 3 How do you reset the maintenance light on a John Deere e130?
- 4 How do you reset a meter reading?
- 5 How do you read an engine hour meter?
- 6 How do you convert engine hours to Miles?
- 7 How do you reset the service light on a John Deere lawn mower?
How do I reset my John Deere hour meter?
Move the throttle lever to slow, and allow the engine to run at a slow idle for a few seconds. Leave the key in this position for two hours, then turn the ignition key to the “Stop” position and remove the key.
How do I reset my hour meter?
The hourmeter, like a car odomometer, can not be reset or turned back. The only options are to make notes of what the correct hour(s) should be or to replace the hourmeter, this is not a warranty failure.
How do you read the hours on a John Deere tractor?
Reading the hour meter is similar on all tractors.
- Climb into the seat in the cab area of the tractor.
- Look for the small rectangular 8-digit odometer built into the dashboard of the tractor. Newer tractors have them digitally displayed on the dashboard so you will have to turn on the tractor to view the hours number.
How does a tractor hour meter work?
The hour meter on a lawnmower acts as a counter. It is meant to track the entire run time from the mower, so you know when specific maintenance tasks have to be performed. The hour meter on a lawnmower is attached to the electrical system, so it only runs when the lawnmower is used.
How do you reset the maintenance light on a John Deere e130?
How do I reset the service light on a John Deere lawn mower? Turn the ignition key to ON, but do not start the engine. Leave the key in this position for two hours, then turn the key to the off position and remove the key. The maintenance timer is reset and activated when the next maintenance interval is reached.
What is the service reminder system John Deere?
The John Deere L130 lawn and garden tractor has a service timer on the dashboard to remind you to do maintenance in a timely manner and keep your mower in top running condition. The timer activates and flashes according to the number of hours of mower operation.
How do you reset a meter reading?
Resetting a meter register to zero
- Open Connect Utility Management > Meters > Enter Meter Activity.
- Enter the Customer Number. Press Enter.
- Select an Action Code. Select the action code to reset a meter reading.
- Press Enter.
- Press Enter again.
- Enter the New Meter ID.
What is hour meter reading?
An hour meter is a gauge or instrument that tracks and records elapsed time, normally displayed in hours and tenths of hours. The majority of hour meters are used to log running time of equipment to assure proper maintenance of expensive machines or systems.
How do you read an engine hour meter?
Read the hour meter from left to right. Most hour meters have a five-digit display. The first digit is thousands, second is hundreds, third is tens, fourth is the single hour digit and fifth is tenths of an hour.
How many hours do tractors last?
As with all machinery, the lifetime of a tractor is largely determined by how well it is maintained. That said, with proper care and attention, a quality tractor should last at least 4000 hours. However, many landscapers and ranchers report running tractors with gauges exceeding 10,000 hours!
How do you convert engine hours to Miles?
Pull the data from the engine meter to determine how many hours the engine has run. Calculate the hours by a factor of 60 to approximate the miles accumulated on the engine. Formula: Engine hours x 60 = Approximate mileage.
How do you reset the hour meter on a John Deere lawn mower?
The hour meter has a reset / toggle button (2) on the bottom right of the display (1). To reset, hold the reset button (2) for 5-8 seconds until the meter reads all zero’s (“00000”). You may push the button to switch between modes until you’re back to the Hour Meter display. Beside above, how does a lawn mower hour meter work?
How do you reset the service light on a John Deere lawn mower?
Just so, how do you reset the service light on a John Deere lawn mower? Turn the ignition key to the “Run” position, but do not start the engine. Leave the key in this position for two hours, then turn the ignition key to the “Stop” position and remove the key. The service timer will reset and come on when the next service interval is reached.
How much does an hour meter repair cost?
Please Note! any new John Deere or 30 series Tractor that are running a CommandCenter™ the price is $1500 USD Cost on any Heavy Equipment Hour Meter Repair on Wheel Loaders, Dozers, Excavators, Skid Steer is $1500 USD Update: Now Supporting John Deere R series Tractors for Hour Meter Repair.