How do you drain a Hotpoint water heater?

How do you drain a Hotpoint water heater?

Draining

1. Turn off power to the unit.
2. Attach a garden hose to the drain valve located at the bottom of the unit and direct that hose to a drain.
3. Turn off the cold water supply.
4. Admit air to the tank by opening a hot water faucet or lifting the handle on the relief valve.
5. Open the drain valve.

How do you drain all the water out of a hot water heater?

Draining Your Hot Water Heater

1. Turn off the water valve that supplies the hot water tank.
2. Attach the hose to the drain valve at the bottom of the water heater.
3. Open that same valve.
4. Open the pressure relief valve.
5. Allow the water to drain.
6. When the tank is empty, turn on the water supply valve.

How do you drain a water heater that has no drain valve?

You will need to shut off the water supply first. By keeping everything closed, the water will drain very slowly, allowing some time to cut and push on the hosebib. It’s like holding you thumb on top of a straw. The tank will be slow to drain if no air can replace the water as it drains.

Can you drain a water heater by running hot water?

Run Hot Water and Open the Drain Valve Run hot water from a nearby tap, upstairs if possible. This allows hot water to drain from the tank and relieves pressure in the system.

Where is the drain valve on a water heater?

There should be a valve on the line near the top of the heater tank. Alternately, the main water supply valve to your home can be shut off.

Is it too late to drain my water heater?

If your water heater is 5 years old or younger Go ahead and do the repair, you should have a few years of life in the tank. This bad boy wont let you down when you are doing your annual water heater drain three years too late.

How do I drain the bottom of my hot water heater?

How Do You Drain a Water Heater?

1. Step 1: Shut off the water supply to your water heater.
2. Step 2: Turn off the power to the water heater.
3. Step 3: Give the water time to cool off.
4. Step 4: Attach a hose to the drain valve.
5. Step 5: Turn on a hot water tap.
6. Step 6: Open the drain valve.

How do you drain a hot water heater fast?

How to Flush Your Water Heater

1. Open the cold water valve. Let the cold water run into the tank for about 15 – 20 seconds and then shut it back off.
2. Shut off the drain valve.
3. Open up the hot water faucets in the house.
4. Turn the burner control back to the on position.

How long does it take for hot water heater to drain?

Open the hot water tank drain valve. Let the water run out the garden hose. This can take 20 to 60 minutes, depending on how big the tank is. Be careful not to damage or break the drain valve when you open and close it.

Are all water heater drain valves the same size?

A standard water heater drain valve for a residential hot water heater is 3/4 in. thread size.

How do you drain hot water from a hot water heater?

Open the drain valve and allow the water to drain from the tank. Again, the water will be hot, so use caution. Once all water has drained from the tank, briefly turn on the cold water supply to the tank. This will stir up any remaining sediment.

How do I Turn Off my hot water heater?

Turn the water supply valve off at the top of the water heater. On the top right side of the water heater is a valve that controls the flow of water into the water heater. Turn the knob or move the switch to shut off the water supply.

What should I do if my hot water heater is leaking?

Water may gush out at first, but should quickly slow to a trickle if the water has been shut off properly. Be sure to leave a hot water tap open in the sink nearest to your hot water heater to alleviate pressure in the system. With your garden hose attached, open up the drain valve.

Attach a garden hose to the drain valve at the bottom of the tank. At the base of the water heater is a small valve called the drain valve. Take a standard garden hose and align it with the threads on the drain valve. Screw the garden hose onto the valve to connect it.