Table of Contents
How do you reset the service light on a Volvo 240?
There is a switch on the back of the instrument cluster behind the speedometer. You can reach up behind the dash to get to the switch, just slide it up and down and the light will reset.
How do you reset the check engine light on a 1991 Volvo 240?
DIY reset service/check engine light
- turn ignition key on, but do not start.
- disconnect the negative (-) battery cable.
- wait 3 minutes.
- turn ignition key off.
- start your car.
How do you reset the service reminder on a Volvo?
Press and hold the trip computer while turning your key to position two. The center arrow will flash red three times. On the third flash, you will let go and an alert will note that you just reset your service light.
How to reset service light volvo 740?
Ignition position I. Press and hold in the reset button for the trip odometer. Ignition position II. NOTE: TURN THE KEY TO POSITION II WITHIN 2 SECONDS! Hold the reset button for the trip odometer pressed in until the original value has been reset.
How do you reset the check engine light on a Volvo 940?
RE: Check Engine Light reset
- key in I position.
- hold trip meter in.
- turn ignition to II position.
- wait until service icon flashes twice.
- release trip odometer button.
Do Volvo 240s have obd2?
OBD unit is in the engine compartment The Volvo 240, 740, 760, 780, 940 and 960 cars from 1989, non-turbo engines only and 1990 to 1995 for both turbo and non-turbo engines were fitted with an On-Board Diagnostic (OBD) unit in the engine compartment.
How do I turn off the maintenance time on my Volvo?
The procedure is similar for all model-years.
- Insert the key into the ignition. Press and hold the trip odometer reset button.
- Turn the ignition on without starting the engine. Continue holding down the trip odometer reset button. Release the trip odometer reset button when the service light starts to flash.
How do you reset the LED light on a Volvo?
Once you put your vehicle’s internal computer into the second position, your oil light will light up on your instrument panel. Keep holding down the button next to your mileage display until the oil light flashes 3 times. Then, release the button to turn off the light.
Why does my Volvo Says Book time for maintenance?
When the “BOOK TIME FOR MAINTENANCE” or “TIME FOR REGULAR SERVICE” light is triggered and you schedule an appointment to have your vehicle serviced, Volvo recommends a series of inspections that will help keep your car in good running order as well as help prevent untimely and costly damages to the engine, depending on …
How do you reset the check engine light on a 2005 Volvo xc90?
What to do if your Volvo ABS light comes back on?
In many cases, a soft reset will turn off the Volvo ABS light. If the ABS light comes back on, have your Volvo diagnosed as the problem will eventually return. The next step is to use a scanner such as iCarsoft for Volvo or Launch Creader to read Volvo ABS module fault codes. Generic OBD2 scanners are not able to read Volvo ABS codes.
When does the Volvo anti skid light come on?
Volvo warning message ABS Anti-skid service required displays on the instrument cluster when the ABS malfunctions. Volvo anti-lock brake system (ABS) light will come on when the ABS module detects a problem with the ABS pump, ABS wheel speed sensors, steering angle sensor, or the ABS control module.
Why is the traction control light on on my Volvo?
If the light stays on after starting the engine, it is an indication that there is a malfunction. Volvo ABS units have a very high failure rate due to faulty solder joints. When the ABS module fails and the ABS light, the traction control light may come on.
Where is the ABS fault code stored on a Volvo?
A fault code is stored in the ABS module that describes what triggered the ABS error. You can use an iCarsoft for Volvo to diagnose the Volvo ABS module. Keep in mind you can’t use a generic OBD2 scanner to diagnose Volvo ABS problems. You can use any Volvo scanner that can read ABS module fault codes.